ElectricityClass 10 Physics Case Study Questions
10 Questions
Generated by KedovoAI
Case 1 of 10
Case Study7 marks
The Household Fuse
The Verma family was preparing for a winter evening. Mrs. Verma switched on a 1500 W room heater. At the same time, her son, Rohan, started using a 1000 W electric iron to press his school uniform. Suddenly, the lights and all appliances in the house went off. Mr. Verma, an engineer, checked the main distribution board and found that the 15 A fuse had blown. He explained to Rohan, 'All our household appliances are connected in parallel to the 220 V mains supply. When you use too many high-power devices at once, the total current drawn from the mains can exceed the safe limit of the circuit, a situation called overloading. The fuse is a safety device, a thin wire with a low melting point, designed to melt and break the circuit to prevent damage to the appliances and wiring.'
Questions on this case
1(1 mark)MCQ
What is the primary reason for connecting household appliances in parallel?
2(1 mark)MCQ
The operation of an electric fuse is based on which effect of electric current?
3(1 mark)MCQ
What is the current drawn by the 1500 W room heater alone?
4(2 marks)
Calculate the total current being drawn from the mains when both the heater and the iron were operational. Explain why the 15 A fuse blew.
5(2 marks)
What two properties must the material of a fuse wire have?
Case Study7 marks
Designing an Electric Kettle
An engineering team is tasked with designing a new electric kettle. Their goal is to create a device that can boil 500 ml of water in under three minutes when connected to a standard 220 V outlet. The core of the kettle is its heating element. The lead designer, Ms. Anjali, considers two materials: copper and Nichrome. She notes that copper has very low resistivity, making it an excellent conductor for transmission wires. However, for a heating element, the requirement is different. She explains, 'We need the element to dissipate a large amount of heat. According to Joule's law, the heat produced is proportional to the resistance. Therefore, we need a material with high resistivity that can also withstand very high temperatures without melting or oxidizing.' Nichrome, an alloy of nickel, chromium, manganese, and iron, fits these criteria perfectly with its high resistivity and high melting point.
Questions on this case
1(1 mark)MCQ
Why is an alloy like Nichrome preferred over a pure metal like copper for a heating element?
2(1 mark)MCQ
To make the kettle boil water faster, the rate of heat production (power) needs to be increased. For a fixed voltage source, how should the resistance of the heating element be changed?
3(1 mark)MCQ
Which formula is most convenient for calculating the power dissipated by the kettle's element when its resistance and the supply voltage are known?
4(2 marks)
If the final design of the kettle has a power rating of 1100 W, calculate the resistance of its Nichrome heating element when operating at 220 V.
5(2 marks)
The resistance of the Nichrome element depends on its physical dimensions. State the relationship between resistance, length, and cross-sectional area of the wire.
Case Study7 marks
Verifying Ohm's Law
A physics student, Priya, wants to determine the resistance of an unknown resistor. She sets up a circuit containing the resistor (R), a battery of 4 cells (1.5 V each), an ammeter, a voltmeter, and a rheostat to vary the current. The voltmeter is connected across the resistor, and the ammeter is connected in series with it. By adjusting the slider of the rheostat, she changes the overall resistance of the circuit and records the corresponding current (I) through the resistor and the potential difference (V) across it. Her observations are recorded in the table below.
| S. No. | Ammeter Reading, I (A) | Voltmeter Reading, V (V) |
|---|---|---|
| 1 | 0.1 | 0.5 |
| 2 | 0.2 | 1.0 |
| 3 | 0.3 | 1.5 |
| 4 | 0.4 | 2.0 |
Questions on this case
1(1 mark)MCQ
What is the primary function of the rheostat in Priya's experiment?
2(1 mark)MCQ
If Priya plots a graph of V (on the y-axis) against I (on the x-axis), what will be the shape of the graph based on her data?
3(1 mark)MCQ
How are the ammeter and voltmeter connected in the circuit relative to the resistor R?
4(2 marks)
Using the data from the table, calculate the resistance of the resistor R.
5(2 marks)
What would happen to the current if Priya replaced the unknown resistor with another one having double the resistance, keeping the potential difference across it the same (e.g., 2.0 V)?