Mechanical Properties Of FluidsClass 11 Physics Case Study Questions
10 Questions
Generated by KedovoAI
Case 1 of 10
Case Study7 marks
The Hydraulic Car Lift
A local car workshop uses a hydraulic lift to raise vehicles for servicing. The lift consists of two pistons, a small one and a large one, connected by a cylinder filled with an incompressible oil. The small piston, with a radius of 5.0 cm, is acted upon by compressed air. The large piston, which supports the car, has a radius of 25 cm. The system is designed based on the principle that pressure applied to an enclosed fluid is transmitted undiminished to every portion of the fluid and the walls of the containing vessel. To lift a heavy SUV with a mass of 2000 kg, the mechanic engages the compressed air system, which applies a force on the small piston. This creates a pressure that is transmitted through the oil, generating a much larger upward force on the large piston.
Questions on this case
1(1 mark)MCQ
The functioning of the hydraulic lift is a direct application of which law?
2(1 mark)MCQ
What is the mechanical advantage (ratio of output force to input force) of this hydraulic lift?
3(1 mark)MCQ
What would happen to the efficiency of the lift if the oil used were significantly compressible?
4(2 marks)
Calculate the minimum force that the compressed air must exert on the small piston to begin lifting the 2000 kg SUV. (Take g = 9.8 m/s²)
5(2 marks)
What is the pressure in the hydraulic oil when the lift is supporting the 2000 kg SUV?
Case Study7 marks
Exploring the Deep Ocean
A modern research submersible is designed to withstand the extreme conditions of the deep ocean. Its spherical hull is made of a high-strength titanium alloy. When it dives to a depth of 3 km in the ocean, the water pressure outside becomes immense. The density of seawater is approximately . The interior of the submersible is maintained at a pressure of 1 atm () for the crew's safety. This creates a massive pressure difference between the outside and the inside, which the hull and the viewports must endure. A circular viewport with a diameter of 30 cm is a particularly critical component, as it must be both strong and transparent.
Questions on this case
1(1 mark)MCQ
The pressure experienced by the submersible at a certain depth depends on which of the following factors?
2(1 mark)MCQ
The 'excess pressure' that the hull must withstand is known as what?
3(1 mark)MCQ
If the submersible were in a freshwater lake (density ) at the same depth, the absolute pressure would be:
4(2 marks)
Calculate the gauge pressure on the submersible at a depth of 3 km. (Take g = 9.8 m/s²)
5(2 marks)
Find the total force exerted on the outside of the 30 cm diameter viewport by the water pressure at this depth.
Case Study7 marks
The Science of Flight
An aircraft's ability to fly is a remarkable application of fluid dynamics. The wings are shaped as aerofoils, with a more curved upper surface and a flatter lower surface. As the plane moves forward, air must travel a longer distance over the top of the wing in the same amount of time as it travels along the bottom. This results in a higher air speed above the wing compared to below it. According to a key principle in fluid dynamics, this speed difference creates a pressure difference. For a Boeing aircraft with a mass of kg and a total wing area of 500 m², this pressure difference must generate enough upward force, or 'lift', to overcome the aircraft's weight and keep it in level flight.
Questions on this case
1(1 mark)MCQ
Which principle best explains the generation of lift by an aircraft wing?
2(1 mark)MCQ
To generate lift, the pressure of the air above the wing () must be _______ the pressure below the wing ().
3(1 mark)MCQ
The shape of the wing ensures that air travels faster over the top. This is an indirect consequence of what principle for an incompressible fluid?
4(2 marks)
Calculate the minimum pressure difference () between the lower and upper surfaces of the wings required to keep the aircraft in level flight. (Take g = 9.8 m/s²)
5(2 marks)
Bernoulli's equation is written as . How is this equation used to relate the pressure difference to the speeds above () and below () the wing?