Mechanical Properties Of SolidsClass 11 Physics Case Study Questions
10 Questions
Generated by KedovoAI
Case 1 of 10
Case Study7 marks
The Skyscraper's Sway
Modern skyscrapers are marvels of engineering, designed to stand tall against various forces, including strong winds and minor earthquakes. To achieve this, they are not built to be perfectly rigid. Instead, they are designed with a degree of flexibility. During high winds, a tall building can sway several feet at the top. This movement is a result of the building deforming under the lateral force of the wind. The internal structure, composed of steel beams and columns, experiences shearing stress. The building's ability to deform and then return to its original shape is a testament to the elastic properties of the materials used. The shear modulus, or modulus of rigidity (G), is a critical parameter for engineers, as it quantifies a material's resistance to this type of deformation. For most materials, the shear modulus is related to the Young's modulus (Y) by the approximate relation G ≈ Y/3.
Questions on this case
1(1 mark)MCQ
What type of strain does the skyscraper primarily experience when it sways due to wind?
2(1 mark)MCQ
The property that measures a material's resistance to shearing stress is known as:
3(1 mark)MCQ
If a steel alloy used in the skyscraper has a Young's modulus (Y) of , its approximate shear modulus (G) would be:
4(2 marks)
Why is it essential for the materials used in a skyscraper to have a high elastic limit?
5(2 marks)
A horizontal steel beam in the skyscraper has a cross-sectional area of and is subjected to a shearing force of . Calculate the shearing stress on the beam.
Case Study7 marks
Deep Sea Submersible Design
An oceanographic institute is designing a new unmanned submersible, the 'Challenger II', to explore the deepest parts of the ocean, where pressures can exceed atmospheres. The hull of the submersible must withstand this immense, uniform pressure from all directions. This type of pressure is known as hydraulic stress. The engineers must select materials that resist compression. A key property they consider is the Bulk Modulus (B), which measures a substance's resistance to uniform compression. It is defined as the ratio of hydraulic stress to the corresponding volume strain. Materials with a high bulk modulus, like steel and titanium alloys, experience only a very small fractional change in volume even under extreme pressure. This is crucial for maintaining the structural integrity of the submersible and protecting the sensitive equipment inside. The compressibility (k) of a material, which is simply the reciprocal of the bulk modulus (), is also a useful parameter.
Questions on this case
1(1 mark)MCQ
What type of stress does the hull of the 'Challenger II' experience at the bottom of the ocean?
2(1 mark)MCQ
A material with a high Bulk Modulus (B) is:
3(1 mark)MCQ
The SI unit for Bulk Modulus is the same as the unit for:
4(2 marks)
A small titanium cube () from the submersible is subjected to a pressure of (approx. 1100 atm). Calculate the fractional change in its volume ().
5(2 marks)
Why is it not feasible to build the submersible's hull out of a material like glass, even though it is a solid? Refer to the properties of materials.
Case Study7 marks
The I-Beam's Strength
In construction, from bridges to buildings, you will often see beams with a cross-section shaped like the letter 'I'. This design, known as an I-beam, is not chosen for aesthetic reasons but for its remarkable structural efficiency. When a beam is supported at its ends and a load is applied to its center, it tends to sag. The amount of sagging, , for a rectangular beam of length , breadth , and depth is given by the formula , where is the load and is the Young's modulus of the material. This formula reveals that the depth is a crucial factor, as the sag is inversely proportional to . The I-beam shape maximizes its depth and places most of the material in the top and bottom flanges, where the stresses are highest, while using a thin 'web' in the middle. This provides a large load-bearing capacity and resistance to bending, while significantly reducing the weight and cost compared to a solid rectangular beam of the same overall dimensions.
Questions on this case
1(1 mark)MCQ
According to the formula, which change would most effectively reduce the sagging () of a beam?
2(1 mark)MCQ
The term 'buckling' refers to a failure mode where a deep, thin beam might:
3(1 mark)MCQ
To minimize sagging for a given load and dimensions, an engineer should choose a material with:
4(2 marks)
Explain the primary advantage of an I-beam's shape compared to a solid rectangular beam of the same height and width.
5(2 marks)
A concrete beam () of length 4 m, breadth 0.2 m, and depth 0.3 m supports a load. If it is replaced by a steel beam () of the exact same dimensions, by what factor will the sagging be reduced?