Alternating CurrentClass 12 Physics Case Study Questions
10 Questions
Generated by KedovoAI
Case 1 of 10
Case Study7 marks
The Appliance Rating
A student examines a new LED bulb for a study lamp. The packaging specifies '10W, 220V, 50Hz'. Her physics teacher explains that for AC appliances, the stated voltage is the root mean square (rms) value, not the peak voltage. This RMS value is the effective voltage that produces the same heating effect in a resistor as an equivalent DC voltage. The household supply doesn't provide a constant 220V, but rather a sinusoidal voltage that oscillates, reaching a much higher peak value in each cycle. The power rating of 10W also refers to the average power consumed over a complete cycle. Although the instantaneous current and voltage vary, and the average current over one cycle is zero, the bulb consistently dissipates energy as heat and light. This is because power dissipation depends on the square of the current, which is always non-negative.
Questions on this case
1(1 mark)MCQ
The 220V rating on the bulb refers to which value of the AC voltage?
2(1 mark)MCQ
What is the peak voltage () of the 220V, 50Hz AC supply?
3(1 mark)MCQ
If this bulb were to be powered by a DC source to achieve the same brightness (i.e., same power dissipation), what should the voltage of the DC source be?
4(2 marks)
Assuming the bulb behaves as a pure resistor, calculate its resistance.
5(2 marks)
The passage states that the average current over a complete cycle is zero. Explain why the average power consumed is not zero.
Case Study7 marks
The Art of Radio Tuning
In the era before streaming services, people used analog radios to listen to music and news. To select a desired station, one would turn a knob, which was connected to a variable capacitor inside the radio's tuning circuit. This circuit, a series LCR circuit, is designed to be in resonance with the frequency of the desired radio station. The radio's antenna picks up signals from numerous stations, all at different frequencies. These signals act as multiple AC sources for the tuning circuit. However, the circuit allows only one frequency to produce a large amplitude current - the one that matches its resonant frequency. By changing the capacitance, the user alters the resonant frequency of the circuit. When this frequency aligns with the carrier frequency of a particular station, the current for that signal is maximized, making it strong enough to be amplified and heard.
Questions on this case
1(1 mark)MCQ
The phenomenon that allows a radio to select a specific station is called:
2(1 mark)MCQ
At resonance in the LCR tuning circuit, what is the relationship between inductive reactance () and capacitive reactance ()?
3(1 mark)MCQ
To tune from a station at 98.3 MHz to a station at 102.5 MHz, how must the capacitance of the variable capacitor be adjusted?
4(2 marks)
Why is the current in the LCR circuit maximum at the resonant frequency?
5(2 marks)
The passage mentions the circuit is a series LCR circuit. Explain why resonance cannot be achieved in a simple RL or RC circuit.
Case Study7 marks
The Power Transmission Grid
Electrical energy is generated at power stations, often located far from urban centers. A major challenge is to transmit this power over hundreds of kilometers with minimal loss. The primary source of power loss in transmission lines is Joule heating, given by , where is the current and is the resistance of the cables. To mitigate this, power companies employ a clever strategy using transformers. At the power station, a step-up transformer increases the voltage from a generator level (e.g., 11 kV) to a very high transmission level (e.g., 400 kV). Since power () is conserved in an ideal transformer, increasing the voltage by a certain factor decreases the current by the same factor. This significantly lower current flows through the transmission lines. Near the destination, a series of step-down transformers reduce the voltage to safer, usable levels, like the 240V supplied to homes.
Questions on this case
1(1 mark)MCQ
What type of transformer is used at the power station to prepare electricity for long-distance transmission?
2(1 mark)MCQ
According to the principle described, if voltage is stepped up from 10 kV to 400 kV (a factor of 40), how is the current in the transmission line affected, assuming an ideal transformer?
3(1 mark)MCQ
The primary reason for using high-voltage for long-distance power transmission is to:
4(2 marks)
A power plant generates 100 MW of power. Compare the power loss if it is transmitted at 200 kV versus 400 kV over a line with a total resistance of 10 .
5(2 marks)
A step-down transformer at a local substation has a primary coil with 10,000 turns and is connected to a 4400V line. If the secondary coil must provide 220V, how many turns must it have? Is this consistent with it being a step-down transformer?