Semiconductor Electronics: Materials, Devices And Simple CircuitsClass 12 Physics Case Study Questions
9 Questions
Generated by KedovoAI
Case 1 of 9
Case Study7 marks
Doping a Silicon Crystal
A semiconductor manufacturing plant starts with a pure silicon crystal which has approximately atoms per cubic meter. At room temperature, its intrinsic carrier concentration () is very low, about , making it a poor conductor. To create a more useful electronic material, the crystal is doped with a pentavalent impurity, Arsenic (As), at a concentration of 1 part per million (ppm). This means one Arsenic atom is added for every million silicon atoms. The Arsenic atoms are chosen because their size is similar to silicon, allowing them to replace silicon atoms in the crystal lattice without causing significant distortion. The fifth valence electron of each arsenic atom is very weakly bound and requires only about 0.05 eV of energy to become free, a value much smaller than the band gap of silicon (1.1 eV).
Questions on this case
1(1 mark)MCQ
What type of semiconductor is formed after doping the silicon crystal with Arsenic?
2(1 mark)MCQ
In the resulting doped semiconductor, what are the majority and minority charge carriers, respectively?
3(1 mark)MCQ
The donor energy level () for Arsenic is located at a specific position in the energy band diagram. Where is it located?
4(2 marks)
Calculate the number density of donor atoms () added to the silicon crystal.
5(2 marks)
Using the law of mass action (), calculate the new concentration of holes () in the doped semiconductor. Assume the electron concentration () is approximately equal to the donor atom density ().
Case Study7 marks
The Formation of a p-n Junction
To create a basic semiconductor diode, a single crystal of silicon is strategically doped such that one region is p-type and the adjacent region is n-type. At the moment of formation, a fascinating process begins. Due to the high concentration of holes in the p-region and electrons in the n-region, a concentration gradient exists across the metallurgical junction. This gradient drives holes to diffuse from the p-side to the n-side, and electrons to diffuse from the n-side to the p-side.
As an electron leaves the n-region, it leaves behind a positively charged, immobile donor ion. Similarly, when a hole leaves the p-region (by an electron filling it), it leaves behind a negatively charged, immobile acceptor ion. This movement creates two layers of fixed charges on either side of the junction, forming a 'depletion region' devoid of free mobile carriers. These layers of space charge generate an internal electric field, which in turn causes a drift current in the opposite direction to the diffusion current. An equilibrium is reached when the diffusion current is exactly balanced by the drift current.
Questions on this case
1(1 mark)MCQ
What is the primary reason for the initial diffusion of charge carriers across the p-n junction?
2(1 mark)MCQ
The depletion region consists of which of the following?
3(1 mark)MCQ
The potential difference developed across the depletion region is known as the barrier potential. This barrier opposes further diffusion. What is its effect on a forward biased diode?
4(2 marks)
What is the direction of the internal electric field within the depletion region? Explain your reasoning.
5(2 marks)
At equilibrium in an unbiased p-n junction, what is the net current across the junction? Explain why.
Case Study7 marks
The Diode as a Rectifier
An electronics student is tasked with building a simple circuit to convert an alternating voltage (AC) into a form of direct voltage (DC). The input is from a transformer that provides an AC voltage of 12 V (peak) at a frequency of 50 Hz. The student connects a single silicon p-n junction diode in series with a load resistor (). They observe the voltage across the load resistor using an oscilloscope. The oscilloscope trace shows that a voltage appears across the load only during one half of the input AC cycle. During the other half, the voltage is nearly zero. The student notes that the diode allows current to pass almost freely in one direction but blocks it almost completely in the other, a property that makes this 'rectification' possible.
Questions on this case
1(1 mark)MCQ
What is the name of the rectifier circuit described in the passage?
2(1 mark)MCQ
If the input AC frequency is 50 Hz, what is the frequency of the pulsating output voltage observed across the load resistor?
3(1 mark)MCQ
The property of the diode that allows it to act as a rectifier is its unidirectional current flow. This is because:
4(2 marks)
Explain why the voltage across the load is nearly zero during the negative half-cycle of the input AC.
5(2 marks)
The output of this rectifier is pulsating DC. What single component could the student add to the circuit to make the output voltage smoother, and how should it be connected?