Electricity: Circuits and their ComponentsClass 7 Science Case Study Questions
3 Questions
Generated by KedovoAI
Case 1 of 3
Case Study7 marks
The Torchlight Repair
Nihal's old torchlight stopped working during a power cut. Remembering his science class, he decided to investigate. He opened the back and found two electric cells. He took them out, wiped them clean, and put them back in. The torch still did not work. He then observed the cells closely. He had placed them such that the flat metal disc of the first cell was touching the flat metal disc of the second cell. He recalled his teacher explaining the importance of terminals. He then examined the small lamp at the front. The thin wire inside the glass bulb seemed intact and was not broken. Finally, he reversed one of the cells, ensuring the metal cap of one cell touched the metal disc of the next. When he slid the switch to the 'ON' position, the torch lit up brightly.
Questions on this case
1(1 mark)MCQ
What is the thin wire inside the glass bulb of the lamp called?
2(1 mark)MCQ
A combination of two or more cells connected together, as in Nihal's torch, is called a:
3(1 mark)MCQ
The torch started working when the metal cap of one cell touched the metal disc of the next. This means the cells were connected:
4(2 marks)
Why did the torch not work when the two flat metal discs were touching each other?
5(2 marks)
If the filament of the lamp had been broken, would Nihal's final attempt at fixing the torch have been successful? Explain your answer.
Case Study7 marks
The DIY Switch Project
For their science project, a group of students decided to build a simple circuit with a homemade switch. They used a piece of cardboard, two drawing pins, and a metal paper clip. They attached one wire from a cell holder to a drawing pin. The paper clip was looped around this pin so it could rotate. The second wire from the cell holder was connected to a lamp. A third wire connected the lamp to the second drawing pin, placed a short distance away. Initially, the lamp did not glow. Then, the group leader rotated the paper clip so it touched both drawing pins. Instantly, the lamp lit up. When they moved the paper clip away, the lamp went off. They concluded that their simple device could successfully open and close the circuit.
Questions on this case
1(1 mark)MCQ
When the paper clip was touching both drawing pins, the lamp glowed. This position of the switch is called the:
2(1 mark)MCQ
What is the primary function of a switch in an electrical circuit?
3(1 mark)MCQ
In this setup, the metal paper clip works as part of the switch because metal is a good:
4(2 marks)
When the paper clip was not touching the second drawing pin, the circuit was considered 'open'. What does an 'open circuit' mean?
5(2 marks)
If the students replaced the metal paper clip with a plastic one, would the lamp glow when the clip touches both drawing pins? Justify your answer.
Case Study7 marks
The Conduction Tester Experiment
Aarav created a simple conduction tester as shown in his textbook. He used a cell, a small incandescent lamp, and two wires with free ends. To check if it was working, he momentarily touched the two free ends together, and the lamp glowed. He then prepared a table to test various items from his geometry box and kitchen. He first tested his plastic scale, and the lamp did not glow. Next, he tested a steel spoon, and the lamp glowed brightly. He then tested a piece of chalk, a graphite pencil lead (testing both ends of the lead, not the wood), and an aluminium foil wrapper. His observations were: the chalk did not make the lamp glow, but both the pencil lead and the aluminium foil did.
Questions on this case
1(1 mark)MCQ
Materials like the steel spoon and aluminium foil, which allowed the lamp to glow, are known as:
2(1 mark)MCQ
The plastic scale and chalk did not allow the lamp to glow. These materials are classified as:
3(1 mark)MCQ
Based on Aarav's experiment, what can be concluded about the pencil lead (graphite)?
4(2 marks)
Why did Aarav touch the free ends of the wires together before starting his experiment?
5(2 marks)
The wires used in the conduction tester are made of metal but are covered with plastic. Explain the role of both the metal and the plastic.